Underwater Magic™ Is based on a formula already used by commercial divers to seal ship leaks , under strict maritime authority regulations on site at the port or out on the open sea.
After further development of the product's formula it has been developed so that it is not only suitable for seawater, it is and since 2009 also resistant against chlorine water and other chemicals.
Underwater Magic™ is a 1 component sea and chlorine water resistant glue, which even seals underwater. It is odour free, it's free of: Oxime - acetic acid - isocyanate & solvents , 100% silicone free and Is not affected by: chlorine / salt (sea) water, weathering and uv light, Aliphatic solvents, oils, grease, diluted inorganic acids and alkalis.
Underwater Magic™ is permanently elastic with good abrasion resistance and good mechanical properties. Temperature resistant from -40°C/°F degrees to +90°C / +194°F, for a short time ( 2 to 3 hours) even to +200°C / +392°F, can fill gaps of up to 40 mm and is allowed in areas close to food.
Underwater Magic™ comes in a Standard 'Silicone tube size' used with a standard caulcking gun with a filling of 290ml (approx. 9.8 US fl. oz.) or as 600ml bag (approx 20.29 US fl. oz.).
*Lifestock needs to be shielded during curing
Underwater Magic™ works at ground level water intakes, skimmers, lighting, overflow-channels, to stone transition areas, concrete and wood
Can be bonded with and to each other!!!
Excellent adhesion on most surfaces without a primer**
** However, it is left to the consumer himself to check the product's suitability for the application in question.
Standars colours white, blue, sand, grey and black.
Preparation is essential, all surfaces need to be solid, clean, free of grease, silicone, algae, residuals of sun cream, old adhesive and anything which could interfere with the bonding, your water need to be in balance (Chlorine / Bromine level in safe swimming pool levels, Ph, Calcium etc) and the water temperature during application needs to be between +5°C and maximum 40°C( 41°F and max 104°F), a shock treatment shall be avoided during curing 5 to 7 days after application.
You should keep your water in balance at all times since unbalanced water can not only be harmful to humans it also can destroy your armatures.
The AP9X Mounting Arm is a sleek, low profile mounting option designed for the new Kessil AP9X Controllable LED Light. The AP9X Mounting Arm allows the fixture to be mounted with just a single arm, providing maximum light spread with minimum intrusion on tank aesthetics. The mounting arm also includes an integrated swivel joint, giving you the ability to easily adjust and orient your light to eliminate shadowing. The unit can be adjusted in height and from back to front (for 18" - 24" wide tanks) and features internal cable management to route power cords through the arm for a flawless finish.
The AP9X is also backwards-compatible with all AP700 mounting options, including the Hanging Kit and two standard Mounting Arms.
Seachem Reef Reactor Lg
Reef Reactor™ is a high-purity source of aragonite, which supplies all important elements for optimal ionic balance and robust coral growth and coloration in reef aquaria. It has a grain size of approximately 1-3 cm. (Reef Reactor™ Md is 0.5 - 1 cm). It is intended for use in calcium reactors where it is dissolved slowly with the addition of CO2. As it dissolves, it provides calcium, magnesium, strontium, potassium, and carbonates among other important elements for reef aquaria. It is excellent at increasing and stabilizing alkalinity, which also supports a stable pH and encourages the rapid formation of coral skeletal material. With high levels of both calcium and magnesium, it offers an excellent means of balanced supplementation for rapid growth and propagation of corals and calcareous animals in reef aquaria. It possesses the highest level of soluble potassium of all competing brands while exhibiting the lowest levels of both aluminum and phosphorus.
Rinse Reef Reactor™ prior to initial placement in your calcium reactor. The rate of water flow through the reactor in conjunction with the pH of the water inside the reactor will control the rate of media dissolution. Follow the manufacturer’s instructions furnished with the calcium reactor and adjust the rates of water flow and CO2 injection to attain the desired concentrations of calcium and alkalinity in the effluent.
Use Seachem’s Reef Status™: Magnesium and Reef Status™: Calcium test kits to measure alkalinity, calcium, and magnesium concentrations.