Skimz Colour-Tracer Silicone Tubing comes in a four useful colours including green, orange, red and yellow.
Tubing is designed specifically for all types of dosing pumps and standard specifications of 4mm ID/6mm OD.
Tubing is extremely flexible, kink resistant, UV resistant, non-toxic and will not harden.
Colour-Tracer silicone tubing helps you easily idenitfy each dosing component and minimize incorrect connections.
All Colour-Tracer silicone tubing are safe to use in contact with food and fully compliant to FDA 177.2600 standard and RoHS Directive (EU) 2015/863.
Length: 2 metres
Aquatic Life Smart Buddie Booster Pump - 50 to 100 GPD
Reverse Osmosis is a pressure-driven process, and RO units thrive on pressure! The reality is that pressure can vary considerably from one municipality to another, and this can have a significant impact on the performance of an RO system. Recognizing the fact that not all pressure is created equally, Aquatic Life developed the Smart Buddie Booster Pump. This value-adding device boosts incoming pressure driving your RO or RO/DI system, thereby enhancing its performance and efficiency. It is designed for use with most 50 to 100 GPD units.
The Aquatic Life Smart Buddie Booster Pump is primarily designed for RO units used in communities troubled by low water pressure. This quiet and easy-to-install accessory is also ideal for hobbyists wishing to harness the full potential of their Reverse Osmosis systems. The Smart Buddie can significantly increase water output, promotes production of the highest quality filtered water, and also helps reduce DI resin consumption for extended usable life. Lastly, it features Buddie Fit press-fittings which make it very easy to plumb into your existing RO setup.
Most residential RO units are capable of operating under lower pressure (down to 35 psi), however they will never reach peak performance under these conditions. Furthermore, water quality may be compromised when units are operated below the 45 psi mark. The average household water pressure is around 60 psi, which should enable most RO units to run properly. The Smart Buddie Booster Pump elevates pressure to between 80 and 90 psi, delivering maximum performance and water quality while reducing waste water production.
To ensure that your RO unit achieves and maintains optimal performance, the Smart Buddie is equipped with an automatic internal flush valve. This handy mechanism flushes the membrane for 18 seconds each and every time the unit is activated. It quickly clears any accumulated debris, effectively prolonging the life of the membrane. To maximize pump life, the Smart Buddie features both high and low pressure switches. The high pressure switch deactivates the pump if the filtered water pressure exceeds 33.35 psi, and the low pressure switch deactivates the pump if incoming water pressure drops below 7.25 psi.
Please Note: the precise activation points of the Smart Buddie's pressure switches may vary slightly from unit to unit. The activation ranges are from 33.35 to 36.25 psi for the high pressure switch, and from 4.35 to 7.25 psi for the low pressure switch. The 1/4" installation tubing required for use is sold separately.
$15.00STAGE 2 – TWIST-IN CARBON BLOCK FILTER CARTRIDGE. Aquatic Life Twist-In Carbon Block Filter Cartridge: Recommend replacing every 6 months. Reduces chlorine and conditions water prior to an RO membrane. Working Pressure: Minimum 35 PSI, Maximum 80 PSI, Ideal 65 PSI.
$28.00STAGE 4 – TWIST-IN MIXED BED COLOR CHANGING RESIN DEIONIZATION CARTRIDGE. Aquatic Life Twist-In Color Changing Dual Deionization Filter Cartridge: Replace when the resin color changes completely. After the water is filtered by a membrane (not included), there is usually a small amount of Total Dissolved Solids (TDS) left in the water. In certain non-drinking water applications, it is important to remove the remaining TDS from the water. This is accomplished by filtering the water through a resin that is charged with Cation and Anion resins (H+ and OH-). As the resin absorbs the TDS, it will change color. When the entire resin has changed color, it is time to replace the DI filter. The new twist-in media cartridge design makes filter changes simple, easy and clean – no tools required and no mess! The twist-in cartridges can be easily changed in only seconds with just a quarter turn and without contact with used filter material. It is important the cartridges are installed post membrane filter to prolong the life of the Deionization (DI) cartridge. Working Pressure: Minimum 35 PSI, Maximum 80 PSI, Ideal 65 PSI.